My throttle cuts off air at about 3500-4000 rpm I’ve tried to reset the throttle sensor ,I’ve disconnected the battery for 30 minutes to reset the battery I have no check engine light ,this problem causes me to have a high idle when I first turn on the car.

This light came on then my truck started driving really rough. It would sort of "jerk" forward when I took my foot off the peddle. Drove it 2 hours home like this but since then it as been fine (only been 4 days). Wondering whats wrong, read online that its probably the throttle body.

I drive around at least 2 hrs or more and 06 f150 you go to mash pedal down to pull out or to go up hill or to pass and truck just shuts off no power anything no lights nothing. I've replaced throttle body, fuel pump control mod. Up by spare tire. Ive replaced fuel filter. Thermostat, air filter , sill have this issue I really would like to drive my truck again. What else should I fix.

Check engine light was on so had auto zone run a scan on it. And at that time my truck would barley creep down the road. Well holy crap a ton of codes parked it till was able to slowly work on it. First changed all spark plugs helped a little then all 8 coil packs. New throttle body new EGR valve. Got a little better new fuel filter. Still ruff idle and cutting out on exceleration. Used smoke machine to check vacuum leaks didn't see any smoke. Checked vacuum line from brake booster that hooks to back of intake seems intact. Brake light stays on mostly sometimes flashes on and off. I'm at a loss help me figure this out. Plz

It starts normally and after a while the revolutions go up and down until it stabilizes again. Like 20 minutes afterwards it starts doing the same until it shuts off. The throttle body was cleaned, the spark plugs and cables were changed, but it does the same until shutting off.

So I bought the truck second hand and it cranks starts and runs very shortly and dies any fuel attempted on pedal and it indefinitely dies everytime idk what I should do and have mechanics background cleaned map and throttle body sensors fuse are good sounds like pump or getting power but again will start and it'll go to about 1500 rmp and then slowly die out what's the best route to fix this being budget friendly

Im getting a P0161 code P1151 p1131 P0156 P0136 P0171 P0184 N0406 codes 1999 ford F150 5.4L I've changed maf sensors ege sensor's and throttle position sensor also blinkers and power mirrors stopped working I've checked for vacuum leaks also it's got me stumped

i have already replaced tthe MAF sensor,cleqned the throttle body just put in a PCVassembly and replaced all 4 02 sensors yet its still throwing P0171

While driving at various speeds, truck stalls occasionally. Rough idle and loss of power as well. I have replaced-fuel pump and control module, plugs and COPs, cam and crank sensor, sent pcm out for testing(good), and pcv valve and tube, cleaned throttle body, had cats looked at(good). Sometimes it happens daily, sometimes I can drive it for a month. I’m ready to scrap it! Advice please.

Truck is running rough, put OBD ll scan on it says lean on banks 1&2. Changed the TPS, also the cold air intake sensor. Nothing works.

I replaced both cams rollers fazers timing chains cam sensors oil pump water pump throttle body throttle body sensors now I’m not getting power to my coils. I have checked all fuses and relays and no codes pop up any ideas?

Ok I got my truck and it runs fine in reverse but when I put it in drive it runs really sluggish and the RPM's are very high . I changed out the throttle body and sensor then I ran a code tester and got the code for the speed control sensor. But none of that fixed my problem it still won't run right in drive . And 💡's

Got a truck from the oldest man on earth, 63k, replaced fuel tank, pump, filter, relay, pressure regulator, and injectors, also plugs and wires and battery, map sensor, throttle position sensor, and it still only starts on ether and won't stay running unless I'm putting ether in.

Says power limit at throttle body

Okay the truck doesn't want to run right it's like it's got no power you can feel it misfire your kick in and off I've got a new ECM I got a new injectors I got a new coil packs I got a new tank I got a new fuel pressure regulator I got a new fuel pump I've got new coil packs new spark plugs cam sensor crank sensor the differential pressure feedback sensor throttle body positioner sensor all this has all been put in here pretty much all new stuff even replace the wiring harness from the ECM out to the engine plug and play can't figure out why it doesn't want to run down the road very good it'll be fine unless it's an electrical issue

My 2010 ford f150 had a throttle body sensor and a mass air sensor replaced n now the ecu reset but i go to drive it and soon i give it gas it falls on its face only drives as idel speed

Replaced throttle position sensor and reset the pcm truck no running soon i give it gas the check engine light and wrench light comes on truck runs bad

I have a 1994 of 150 and I have replaced the spark plugs wires throttle positioning sensor clean the throttle body remove both cats and put a piece a straight pipe in their place and also replaced the Ignition coil and clean the mass air flow sensor and still the truck doesn't react to me pressing the throttle until I have it to the floor and just recently I started backfiring.

Tps and throttle body test good. It's been in failsafe mode but now it won't allow the pcm to be reset. Eve put a new pcm in no change. Throws a ton of codes. Please help

Cranks but won't fire up changed everything. Throttle body throttle position sensor fuel pressure regulator