I’m having a lost of communication with abs module and a bunch of wiring lights on the dash

Sometimes the car stumbles then stalls right when I stop

I pulled the old battery off for about 5 day's. Replaced with a newer one, and my issue is it won't turn over ,When I turn the key on all the lights on dash is on including theft light I checked connections and tested relays and checked every fuse. Still won't crank. In leaning towards anti-theft or safety switch in the shifter. Any in put would be a great help. It's a 2006 v6 mustang.

While driving car runs fine when I come to a stop or red light engine shuts off but restarts when I start it

I recently bought a 2014 Mustang V6. The check engine light is on, and when I scanned it, it showed a crankshaft position not learned code. I already changed the crankshaft sensor, but the problem persists. The RPMs fluctuate when the car is stopped, and it feels like it's about to shut off. Also, it doesn’t accelerate properly—it takes a while to respond. Could you help me figure out what the problem might be? Thanks!!

I am try somethings but has still say check inlet or something

Brakes will do fine for a few days and then release after stops consistently slower until they simply don't let go. Tow it home or to the shop and let it sit for a few days and fine again. There have been two separate occasions where the collision prevention system randomly activated and it stored codes. It said hill assist unavailable and abs fault. Took it to the dealership and they charged me $250 something to put it on the diagnostic machine and tell me it's the rear speed sensors and the purge valve for the evap canister. Fixed all 4 speed sensors for good measure and the purge valve. Sti… Read complete

Car died on your interstate do turn old battery put new battery in car started and now speedometer don't work

Can't fine the issue with this code. Replace transmission position sensor but still have O/D off flashing. Check engine light on and car in limp mode. Any help would be appreciated

So i changed out my ignition cylynder when i noticed the key was getting stuck. Now after taking out the old one i am having trouble putting in the new one as well as the gear and retainer. The car has no power despite it having a brand new battery. The only thing that even makes a sound is the door chime! lol please help i just want to drive my beautiful car again...

I parked the car for a year but now its not changing gears and it turned on the OD drive lite on the dash

Getting up to speed the car will shift to 2nd and then keeping the acceleration up, it wont shift to 3rd unless I let off the accelerator, then it will go into 3rd, and then it flashes the engine light and will run like shit for a little bit, until the light goes off and will be back to normal, until I kick it down again.

I have replaced O2 sensors 3 times this last I got some good ones what is funny in my code reader it shows green for smog ready but show there is a problem with that sensor I have traced every wire in it how I know there is a short I disconnect the negative cable and put a test light on it the. I out the light on the post and it lights up not to bright so I kinda stuck although I can't get to too if the transmission to check for broken wires plus have a new pcm gie it need to find someone that know what they are doing she run great I. An not get rid of the check engine light and in the live data b2s2 reads 0000rhe other ones read 99.90 when at temperature

I accidentally flipped the terminas when jump starting my vehicle. The main fuse blew up and I replaced it. But the steering wheel buttons do not light up, they're working but not lighting up even when i switch on the headlights manually (not uing auto), this also applies to the (traction/hazards/trunk) button. Every single button in the car works and lights up, but these buttons work with no back light.
I tested the fuse box, some fuses were blown and got replaced, and i did test the fuses after replacement to check if something blew up again due to a short circuit, but its all okay.

I decided to mess with the fuse box one day and unfortunately pulled a couple of fuses that I didn’t know what they were or if they were long story short, the car won’t start the battery charges. The key turned over and the dashboard lights come on you can run on the windows, etc. but the car will not turn over. It makes a clicking sound and somebody said that we needed a new what was it called Something new but I bought the parts. Just wondering if anybody had any suggestions

It seems when I let the car sit idling for a little bit when it’s up to operating temp it seems like it smoked but it’s not smoking it seems to have a odd smell it it as well and I can’t figure out what it is I’ve checked for leaks in anything everywhere and there are none even the ac stays nice and cold whenever it does it tho it smells minty

Over drive lights is flashing and engine light is on I’ve replaced the solenoid pack transmission filter fluid and pcm I have no idea what else it could be

My o/d light keeps blinking.. it stop for a few after I pulled a fuse relay and when I cut the car off and crunk it back on the o/d light started flashing again

Finding fuse 8 inside blow for pcm with multiple emission codes. As replacing the 20 Amp fuse no engine light but the car will start but wouldn't stay running. Then pulling out the fuse car would start but as it's running putting the fuse back in car would stop running. Please help so confused.

the engine light is on and there might be excape of oxygen.