Problèmes Check engine light

Check engine light
Check engine light: It indicates that there is a failure in the way the engine works, specifically in the exhaust system. When it blinks, the failure is serious.
Lire la suite
Problèmes liés :

Meilleurs problèmes

Check engine light, 3 codes (U01BO, U0284, U1345)

Chevrolet Malibu 2020 LS 1.5 turbo 86020 km
The other day my check engine light came on. I put a code reader on it and it threw 3 codes. U01B0 (Lost communication w battery sensor), U0284 (Lost communication w active grille air shutter I motor module) and U1345(Engine Control Module LIN Bus 1. I checked all fuses, checked for damaged wiring, nothing. So I replaced the battery monitor module. Same problem. At first, my fan would be running going from slow to fast and back again the entire time, but that has stopped. I've checked the voltage on the lin bus wire coming from the negative terminal of the battery, apparantly it should be fro… Lire en entier
Jayp156 de États-Unis il y a 2 ans  
JA
6 signalements 
Jayp156 de États-Unis il y a 2 ans
Still unresolved, and no comments. StartMyCar asked me to make this comment.
Dan1020 de États-Unis il y a 9 mois
Were you able to resolve this? I currently have the U0284 causing my check engine to be lot up right now. Let me know and thanks!
Commenter

Check engine light

Chevrolet Malibu 2010 2.4 14700000 km
I was getting a check engine light, I check with a scanner and the evaporator canister was bad,I replaced the check engine light went out for three days and came back up the we try scanning it again and it says no information there is no communication with the car and the scanner
Willy de États-Unis il y a un an  
WI
2 réponses 
Willy de États-Unis il y a un an
I have a 2010 chevy malibu 2.4 Ls I took it to emissions and it pass but couple days latter the check engine light came on,I check with the scanner and it turns out that the the vapor evaporator sensor needed to be replace,I replace that sensor and the check engine light went out but 3 days later came back on I try to scanned again and shows no information on vehicle try again but still no comunication,took it to my mechanic and he said there is no issues with the engine it shows everything is OK in the engine and tha the problem could be a short somewhere any suggestions appreciated
Thank you
Willy de États-Unis il y a un an
Unfortunately the problem with my 2010 chevy malibu engine light hasn't been solved after trying everything posible on my part so I'm thinking about taking it to an ethnic technician to get a diagnostic to see what's going on I mean the car runs good, everything else is OK so I figured why not go ahead and fix it
Commenter

Engine light is on

Chevrolet Malibu 2016 Engine light  164350 km
Nothing wrong with the engine but the light is popping in and out all the time and it affects other features
Harry de Canada il y a 6 mois  
HA
2 réponses 
Lilbit de États-Unis il y a 6 mois
From what I found the corporate is likely going to be in O2 sensor either right before aka the Upstream sensor before the catalytic converter or the downstream sensor the one after the catalytic converter. That would be my suggestion on checking
Harry de Canada il y a 6 mois
Do you think it can be fixed at home if yes then how. Thanks for your help
Commenter

At 60 to 70mph engine light comes on saying to service stabilatrack

Chevrolet Malibu 2018 sedan 1.5 4clylider 149900 km
At 60 to 70mph engine light comes on saying to service stabilatrack the car feels Shakey at high speeds and my ac also stops working when I'm parked but when I'm driving its on
danny de Trinité-et-Tobago il y a 6 mois  
DA
3 signalements 
Jbrokaw de États-Unis il y a 5 mois
Check you break pedal sensor and the gas pedal sensor located in the pedals.
Commenter

Engine Light

Chevrolet Malibu 2014  146000 km
Engine light comes on every so often, then goes away. Gas cap is in tight.
TexasMom de États-Unis il y a 3 mois  
TE

Engine light comes on and car goes into limp mode

Chevrolet Malibu 2014 lt 100000 km
I get code p0091 for a 2014 Chevrolet Malibu.
byrd de États-Unis il y a 4 mois  
BY
1 signalement 

Check engine light

Chevrolet Malibu 2022 Malibu  98839 km
Check engine light is on, shows codes U18A2 & U0101, Car lights come on, ignition doesn’t start, able to shift gears but car stays in neutral position, all power related to the battery is working
Malibu de États-Unis il y a 6 mois  
MA

Won't start

Chevrolet Malibu 2011  147000 km
2011 Chevy Malibu replaced battery not it, replace relay fuse not it, car runs then next day won't start. I have radio, lights air conditioner lights on dash as soon as I turn key over nothing. All lights on dash gone not check engine light my daughter owned this car 3 years never a problem. The mint she paid off now this I called car lot to see if they removed the don't start tracker and they removed that. I really thought that was the problem but guy said no. Need help before I take a sledge hammer to the whole car at my wits ends.
Lisa de États-Unis il y a 2 ans  
LI
10 signalements 
MzRobin de États-Unis il y a 2 ans
Get a scan tool at AutoZone or O'rielly, or wherever. Turn your key on, connect it like a phone charger to your car. It should be near the gas pedal and look in front of you or in that area. The port to plug it into is going to look like the end on the scan tool. Follow instructions. It will tell you what's wrong with your car, if it's an electrical problem Could be a camshaft sensor, a crankshaft sensor, theft deterrent system, a loose or bad ground wire, I've seen it be a fuse, not a relay, a simple fuse! I've known it to be the entire fuse box under the hood was traded out with a used identical one. We swapped our fuses in to the newer box, the car started right up! Nobody could fix this car not even GMC CHEVROLET dealership! We did...hope this helps.....
Lisa de États-Unis il y a 2 ans
I did that nothing comes up on the scan tool. It reads nothing, I did notice at the battery for the positive cable the wires are crushed, and their is black sticky stuff on it. I took terminals off this because it had broke when tightened. I replaced it and noticed the cable. I going to try to get the black sticky stuff off and see if that helps. I will try to upload a picture for before and after. Thank you for the info on the scan tool but it literally shows nothing.
Faris de États-Unis il y a 2 ans
I think i had the same problem on my 2010 check this video out https://youtu.be/tNMRbT1nZOk?si=EYXOi0…
Rhonda de États-Unis il y a 2 ans
I don't know if your battery is the very large one with 4 or 5 wires plus negative & positive terminals. If so it sounds like the wires are loose. My car did same exact thing. I removed all wires. Connected the little wires making sure the nuts were good and tight, then connect positive and last negative. It matters! Making sure all connections are clean. I was praying it would work but I didn't really believe it would. It sounded too easy. I said I don't think it's gonna work because I didn't hear the bell dinging because of opened door. Just as I finish saying that I heard the dinging. It cranked right up and all was good. No lie. I was so freaking happy!
litz de États-Unis il y a un an
If you don’t see anything on the scan tool after connecting your scanner, the problem would be most likely your ecu or ecm…its not communicating with your scanner and likely it’s already worn out…you may be the only one who possibly know the cause of its issue like flood, engine overheating etc…therefore in order to properly navigate this kind of electrical problem since you don’t have anything on your scanner …I strongly advise it’s your ecm need to be replaced and maybe even your bcm also as this two like husband & wife that has marital relationship with each other…hope this kind of technicality will help you pinpoint the actual issue
Commenter

Can not pass Emmisions to re-register my car RésoluRésolu

Chevrolet Malibu 2009 2.4 212000 km
Check engine light and the car continues to shut down to reduced power service esc service traction all these warnings. I have had code for the purge valve the canister vent valve the fuel pump the throttle body and have replaced all of these things reset codes and while driving through the first cycle the car all the sudden the engine power gets reduced and i have to pull over the engine light and traction control light are back on and so i start the process again I can not pass emissions please anyone
MizMalibuBlues de États-Unis il y a 4 ans  
MI
6 signalements 
Yasir de autre il y a 3 ans
Exactly same issue with my Malibu 2011. Anyone help please.
Résolu
Meilleure réponse (selon MizMalibuBlues)
Aces de États-Unis il y a 2 ans
My code is P0449. This is Vent Valve Solenoid Circuit. Knowing that a gas cap is first thing to change I did that. Checked emission fuses,all good. Changed purge valve,nothing. Check engine light still on.
Commenter

My car isnt running correctly

Chevrolet Malibu 2000 Mid size saden 53000 km
My car is like bucking like some thing is holding it back from running freely and my check engine light is on im a single mom and i have no idea whats wrong with my car
Jeanette de États-Unis il y a 10 ans  
JE
4 signalements 
Lauren de États-Unis il y a 8 ans
U probably don't have a vacuum seal in the cold air intake stsytern it happened to mine it's an easy fix tho u can do it urself I can tell u how or you tube can
Commenter

Brake pedal hard to push, car won’t start

Chevrolet Malibu 2018 LT 1.5 103944 km
I have a new battery and brand new starter, but car still won’t start, it just clicks. My brake pedal is really hard to push and now in neutral tires won’t roll. Check engine light on but no error codes are showing up. Sent to dealership and they said it just needed a starter.
Tink Tink 2.0 de États-Unis il y a un an  
TI
3 signalements 
Bill F de États-Unis il y a un an
Same thing happened to my 2016 LS. I drove it to a benefit raffle and it was fine. Found out I won a raffle so I had to go pick it up and when I tried to start it the brake was stiff and when I pushed the start button all the lights started flickering and I heard clicking sound. It wouldn't stop until I figured out I had to push the start button twice. Since then I put a new battery in, replaced the vacuum pump, changed the oil and it still won't start. I'm about to give up and call AAA to get it towed to the dealer.
Commenter

Gauges and infotainment stopped working

Chevrolet Malibu 2020 1.5 turbo  102000 km
My radio and usb ports and gauges went black just stopped working I replaced the battery and still nothing I thought maybe the car was going wack bc of the battery but I still have a check engine light on my dash it’s there for a camshaft sensor but nothing else works I can’t change the hvac it’s stuck on defrost now but the car runs and drives perfectly fine
Lowkey de États-Unis il y a 8 jours  
LO

Hot start issue / No start when warm after replacing brake vacuum pump

Chevrolet Malibu 2016 sedan 1.5L Turbo 270000 km
After replacing the OEM brake vacuum pump, engine oil, filter, and crankshaft sensor, the car starts perfectly when cold. However, once the engine gets hot and I turn it off, it completely refuses to restart until it cools down. Fuses and mechanical parts are fine. There is no Check Engine light and no codes on the scanner
moe4 de Canada il y a 3 mois  
MO
4 signalements 

Stupid autostart

Chevrolet Malibu 2014  91000 km
While stopped at light, the car engine stops and then won't restart. Had to push car off to the side then put it in park and after a few minutes was able to restart. My mechanic pulled the power censor wire to the hood that bypasses the autostart (so it is able to drive) but caused the engine light to turn on and the remote start will not operate. Already replaced both batteries. I hate the autostart!
cwdebkj de États-Unis il y a 6 mois  
CW

Cooling Fan

Chevrolet Malibu 2019  59850 km
When I shut off the car, a fan continues to run for a few minutes. Now I have the engine icon coming on. My coolant level looks fine. Should I try to change the "60" relay fuse next? I have only had the car for one month, so I am not familiar with the Malibu.
Shirley de États-Unis il y a 7 mois  
SH
1 signalement 

No crank no start

Chevrolet Malibu 2006 3500  160000 km
So I was on the freeway headed home and when I got to the red light on the off ramp. I waited for green light and suddenly no warning my car just dies. When I went to try to start it back up no crank no start. After it stalled I am getting a check engine light however I plug in the code reader and it shows 0 codes... help please.
Billy de États-Unis il y a un an  
BI
2 signalements 

Stalled out and wouldn’t come back on

Chevrolet Malibu 2011  92300 km
Car completely stalled no check engine light. When I turn the ignition it’ll start to turn over and immediately lose power
Luis de États-Unis il y a un an  
LU
1 signalement 

2016 chevy malibu P1682 no ac/cooling fans not running Help!

Chevrolet Malibu 2016 limited LS/2.5 L. FI DOHC 89529 km
My AC is n9ot working the compressor isnt engaging. There is refrigerant pressure in the lines. I tried to add some refrigerant (very small amount) to see if clutch engaged but no good. I checked fuses all seemed fine i tested. What i9 d9id notice was when ac was activated on dash and air turned high the cooling fans arent turning on. Also, a check engine light is on with code p1682(ignition 1 switch circuit 2) and p26E4 also C0242-00 (power train control module traction control). This is as far as i got. There is power going to the fans where the connectors plug in. I thought of a pontiac g6… Lire en entier
R.S Garage de États-Unis il y a un an  
R.
3 signalements 

Issue with ECS Power stearing with other faults that come on

Chevrolet Malibu 2021 1.5-liter four-cylinder, LT 122222 km
It's very random, but some mornings my Traction light will come on, and my display will say service ESC and Reduced steering. Also, the parking assist and Forward collision Alert will come on right as I put it into reverse. I first started noticing last fall that the parking assist would turn off randomly and my radio would look like the colors were not aligned that has fixed itself, but the parking assist has brought the ESC problem on a frigid day this last December; the car almost didn't start. And now, at least once a week, it will turn on for the day and go away for the rest of the week. No check engine light just the little car skidding.
1
2
3
RU12 de États-Unis il y a un an  
RU
1 signalement 

No accelerating properly

Chevrolet Malibu 2016 2.5 5500 km
Check engine light on and the car 9nly accelerating 40mph
Benny de Bahamas il y a 8 ans  
BE
1 signalement 

Transmission

Chevrolet Malibu 2009 manuel 111048 km
Just purchase this 2009 chevy malibu just two months ago. Now the engine light is on and saying codes po716,po717.
rosecook6rose de États-Unis il y a 9 ans  
RO
1 signalement 
Des problèmes avec ta Malibu ? Partage-les
Envoyer le commentaireAnnuler
Envoyer la réponseAnnuler


Recherches populaires
RadioClutchOverheatingFusebox