Engine problems

Top problems

Engine wont start

Ford Ranger 2016 Ford Ranger Wildtrak 3.2  35000 miles
Hey guys i have a problem with my 3.2 ford ranger wildtrak... after 3 days in garage the engine wont start... i thought it was the battery so i change the battery with a new one... but still it wont start... i describe it that the starter fails to continue to rotate and to start the engine... it rotates but it stops. Something is forcing the engine not to start... there are no indication lights on my dash board... do anyone have the same problem? my impression is the starter... any ideas?
G. R. from other 5 years ago  
G.
38 reports 
John from other 3 years ago
Same goes in ours may I know what fix your problem?
Nokesy from Australia 3 years ago
This is mine today, anyone know the issue?
Karl1975 from Australia 3 years ago
Hey mate, what did you find the problem was, mine has just started doing the same thing.
Luke from Australia 3 years ago
@Karl1975Did you find what it was I now have one doing the same thing
Karl1975 from Australia 3 years ago
@LukeHey mate it was a loose wire on the battery terminal, not the terminal itself but one of the wires that bolts to the terminal.
Cinnymel from United States 2 years ago
Yes. My 2002 Ford ranger xlt v6 3.0l truck wouldn't start. Installed new battery, even though battery, voltage regulator, alternator, starter all checked out good. I put a new Ford ignition starter coil pack module that goes where a distributor cap used to in older cars and it fixed problem so far. It was part of control computer chip.
Cinnymel from United States 2 years ago
Has anyone else experienced manual transmission problems. I have a 2002 Ford Ranger xlt v6 3.0l and have had the clutch and manual transmission fixed in October of 2020. $1600 at automotive shop which counted tge Emergency brake cable broke and rear disc drums replaced. Now, a year and a half later gears are sticking and doesn't want to go into gear.
Florida D from United States a year ago
The roll over switch Up under the passage side below the glove box
HENDO from New Zealand a year ago
Scan and clear all fault codes , should fix it.
Cooraz from Australia 2 months ago
Maybe need to reset the battery monitor sensor. In the new models there's a 'turn ignition/ press brake' - sequence... but I'm not sure how or if you can do it yourself in older models. Need a mechanic with a computer to hook up to it and reset the battery monitor sensor. Takes all of 10 seconds to do. Ask them how much for a call out to do it and haggle them with the leverage that it will only take them 10 seconds of they try charging anything too ridiculous.
Comment

Engines cranks but won’t start

Ford Ranger 2006 2.5 turbo diesel 302000 miles
Engine emits smoke whilst cranking but won’t start. End up with battery being flat
Rams from other 3 years ago  
RA
5 reports 
Emeka from Nigeria 3 years ago
Engine starts only when fuel us introduced to manifold but shuts down when it dries out.
Dimakatsi from South Africa 3 years ago
Its jst stopped while running & Engine emits smoke whilst cranking but won’t start again. End up with battery being flat
Comment

At times engine cranks over but will not start up

Ford Ranger 2016 XLT 3.2 4wd ute 29000 miles
Random problem has happened about 8 times since new when hot or cold. Usually I lock and unlock car then retry starting again. Just guessing here but the delay of a few mins does let me start successfully. Any ideas?
Have taken to Ford for advise...?
Must be a common thing surely
Dougie from Australia 6 years ago  
DO
4 reports 
Dougie from Australia 6 years ago
Ford sorted this for me by replacing the crank angle sensor. They were very happy to help. Perfect now.
Comment

Engine cut out

Ford Ranger 2014 Ranger 60000 miles
My ford ranger just suddenly cut out engine while im driving i have to wait a few minutes for it to start again after that it can go a day or more with no issues before suddenly cutting out while im driving. I have bought to garage and they have checked the ecu they told me no problems ,but im still getting this issue and garage up to now cannot find the fault as it does not show anything on the diagnostic machine.
Island vibes from other a year ago  
IS
1 report 
Desie from United Kingdom a year ago
There was a problem with the fuel injection system of cars manufactured between 12 September 2014 and 26 January 2015 where fuel pressure could be lost and cause the engine to cut out. Dealers were to inspect the injectors and replace if necessary. Unintended downshift
Comment

15 amp engine fuse

Ford Ranger 2001 2.5 diesel turbo, wlt motor 340000 miles
Hi my 15 amp engine fuse keeps blowing, turns off the whole engine, won't start and the glow plug lights won't turn on. What can be the cause of the fuse to keep on blowing every time?
1
Clarissa from South Africa 2 years ago  
CL
1 report 
Sello from South Africa 2 years ago
Same issue here did you finally get the problem sorted?
Clarissa from South Africa 2 years ago
Hi, well to make the story as short as possible. We stripped the whole dash area and checked for loose connections, fixed what looked like it needed to be fixed and that was it. We still don't know what exactly the problem was. But the bakkie is driving now so thank goodness. I wish I had a clear answer myself.
Comment

Refusing to give fuel to the engine

Ford Ranger 2010 Truck single cab 3.0 tdci diesel xlt 90000 miles
It is cranking and not giving fuel to the engine and it has been still for two months
Brad from South Africa 9 months ago  
BR
1 report 
Siyabonga from South Africa 8 months ago
It doesn't open pump and no current on injectors
Comment

Engine cranks won't start

Ford Ranger 2016 Duel cab Disel 3.2 81000180000 miles
Engine will crank but won't start after finding one injector line weeping
Charly from Australia a year ago  
CH
1 report 
Bruce from United States a year ago
It sounds like the issue may be related to the fuel delivery system. The fact that you have found a fuel injector line that is weeping, or leaking, could be causing a lack of fuel reaching the engine, leading to it not starting. It's also possible that there could be an issue with the fuel pump or fuel pressure in the system. I would recommend having a mechanic diagnose the issue and determine the root cause. They will likely need to perform tests on the fuel delivery system, including checking the fuel pressure and flow, as well as testing the fuel injectors and pump to see if they are functioning properly. It may also be necessary to replace any faulty components in the system to get the engine running again.
Comment

Engine problems

Ford Ranger 2012 Manual  175000 miles
I have a 2,2l ford ranger cuts off when lm driving when i check or wait for sometime it starts. So lve checked that solenoid of injector is hot
A1983 from South Africa 3 months ago  
A1

Engine and ignition issues

Ford Ranger 2017 Wildtrak  62000 miles
Doesn't start with ignition, thought it's a starter, turn the key to on, powered starter directly then boom starts perfectly, test drive turn ignition key off, engine keeps running, what could be a problem and how do I resolve it
Modise from South Africa 3 months ago  
MO

The engine cranks but won't start

Ford Ranger 2013 Pick up Qj2l  275691 miles
The engine cranks but won't start, it's a diesel engine
Mast from South Africa 3 months ago  
MA

The engine start okay, when it is cold. When the temperature reaches

Ford Ranger 2017 Utility 2147345 miles
Normal operating temperature, it cuts off (engine). When restarting, the engine rev is not steady and eventually it cuts off.
MANDE from other 9 months ago  
MA

Engine start

Ford Ranger 2012 Club cab,2.5tdi 215670 miles
The battery is good & the heater plugs are good,I do pushing start the engine runs good. Problem is when I do start with the keys don't start only get on.
Rufus from South Africa a year ago  
RU

Engine cranks but will not start. White smoke from exhaust

Ford Ranger 2013 Ute 290000 miles
I noticed the idle hunting while stationary and decides to head home so i could inspect the issue. When i clutched in to come to a stop at an intetsection the ute stalled. Having not come to a complete stop i let the clutch out to roll start the ute and huge amounts of white smoke came from the exhaust and the ute would not start. *Engine cranks but will not fire,
*No DTC codes
*Replaced fuel filter
Mikejohnoh from New Zealand a year ago  
MI
6 reports 

Engine lose of power

Ford Ranger 2013 Tray back 220000 miles
Engine starts then after few minutes engine starts making noise and loses power to accelerate
Stuart from Australia a year ago  
ST
3 reports 

Sound system fuse. Clutch failure. Engine failure to

Ford Ranger 2018 Ranger supercab 2.2  173000 miles
Sound system power failure since new. Clutch failure on 115000km. Engine failure on 173000km
Jakes from South Africa 2 years ago  
JA

Engine won't crank

Ford Ranger 2019  9000 miles
Have a 1.5 year old 2.0 bitubo ranger. On hitting the push start button, engine won't not crank and dashboard icons lights will come on. However, trying again after a few minutes will always work. This phenomenon is intermittent and recurs once every 2 to 3 weeks. The service center had change out the starter relay, but the issue happened again after 8 weeks. I appreciate any suggestings on what could be the problem... As this had been dragging for the past months. So far, Ford warranty center could not solve my problem. Thanks
NicTeng from other 3 years ago  
NI
7 reports 

I put a 4 cylinder 5 speed engine in my Ford Ranger 2. 5 liter change

Ford Ranger 2001 Pic up 220008 miles
The truck won't start it acts like it's getting no gas if I pour gas in it or starting die
Tommy from United States 5 years ago  
TO

Engine top end noise

Ford Ranger 2017  7000 miles
When cold the top end rattles until warm. I have borrowed a new 2018 model and the problem does not occur. This is what highlighted the issue on the 2017 model.
DavidC from New Zealand 6 years ago  
DA
1 report 

Do I have to program anything after engine change

Ford Ranger 2007 3.0 128000 miles
Want to change engine and don't know if I have to program anything after the change over
Johny from Australia 6 years ago  
JO

Strange engine noise after it has warmed up

Ford Ranger 2010 deisel3.0 100000 miles
With all belts removed the noise can be heard from front or drivers side of motor
snake from Australia 7 years ago  
SN
20 reports 

engine won't start if does cuts out when I pull off

Ford Ranger 2006 Ford ranger 2.5 97000 miles
When pulling off first thing engine cuts out as though there is no power fuel gage drops when going if put in reverse/ i use electric windows does the same ,lights still on dash still lit but no power turn key and hold engine starts put in revers stops as if no power going threw
Chris from United Kingdom 7 years ago  
CH
7 reports 

Cutting out at junction once engine is hot

Ford Ranger 2004 Manual  100000 miles
Cutting out at junction when engine is hot
RomcadRomcad from United Kingdom 8 years ago  
RO
11 reports 

Cranking but not starting when hot SolvedSolved

Ford Ranger 2013 Ranger 3.2 233456 miles
First thing in the morning start with one kick , but if you drive about 7 km and it comes to temperature and you switch the engine off , she will not start again until cooled down
Green Monster from South Africa 3 years ago  
GR
Rank 5
27 reports 
Solved
Best answer (according to Green Monster)
Green Monster from South Africa 3 years ago
I took it to a very friendly Ford agency that informed me it is a common problem on the 3.2 , some shut off valve on the high pressure pump and replaced all injectors , the bleed-off on the injectors gone out of spec and not repairable.
Cooraz from Australia 3 years ago
It’s the cam sensor. Just replace it and all will be good. Only costs about $120 Australian. And 5 - 10 minutes time of your mechanic.
Gringo from Trinidad and Tobago 8 days ago
@CoorazDid that still no start
Comment

Engine check light SolvedSolved

Ford Ranger 2008 3 lt Diesel  108000 miles
Hi my engine check light came on 2 days ago & my truck stalled & the OBD reader said code 93 & 191 is there any way to find out why, please resond if you know what could be the cause of it.
Regards. Duke...
Duke from Australia 6 years ago  
DU
4 reports 
Duke from Australia 6 years ago
The Engine Code p0191 is the Fuel Sensor Unit , after reading & seeing your video on how to remove & fit it I new that I could do it myself. I went to my local Ford Dealer & told him what I needed & how much was the Sensor Unit, my local Ford Dealer said that I would have to buy the whole Fuel Rail because they don't make them as a Single Unit & the price would be $800 + Fitting the. Rail with the Sensor, I showed this Idiot your video clip & he told me that your video was Wrong , so I told him too shove it I then went to a Spare parts shop & told them what I needed & they had 1 in stock for $370 , all I had ro do was to unsrew it the 1 in the video had 2 bolts but on mine ir was just unscrewing it , so easy I let my truck get COLD when I done the JOB, it took about 20 mins from start to finish. When I took the old part back in they said it's a non - genuine part , I told that Idiot that I would rather have a Bosch part than a Ford part. I just think that this Ford Dealer justs likes Ripping people off & if I ever need any parts in the future I will NEVER go back there. Best regards , Duke
Wiselaw from Australia 6 years ago
My 2008 turbo Ranger just got wrtten off by insurance co after months of exhaustive independent engineer inspections after filling it with contaminated fuel at Woolworths /Caltex discount fuel. Just salvaged it as economic write-off from Pickles Auctions and would love to see link to the video you mention. The truck was my late Daughter's veterinarian truck so has great sentimental attachment.
Solved
Best answer (according to Duke)
Yeah Right from Australia 3 years ago
Its typical of dealers. They are a bunch of rip off merchants!
Duke from Australia 3 years ago
Mate I only go to Bursons if I need anything, my local fFord Dealer charged an old lady $70 to replace her new battery that she brought in, bloody thieves, Not happy JAN 😡🇦🇺
Lebo from South Africa a year ago
Hi 3.0 TDCi Ford ranger it doesn't show engine light
Comment

Diesel in the oil sump SolvedSolved

Ford Ranger 2015  236500 miles
I just my engine run away on me a day ago just switched all off now i drained all the oil and i find there's diesel in my oil what can cause this thanks i was thinking high pressure pump for common rail thats the only item that can make sense thanks
Basie from South Africa 3 years ago  
BA
19 reports 
Solved
Best answer (according to Basie)
Giffie from South Africa 2 years ago
Same here whatsapp me 0796693697
Hawk02 from South Africa a year ago
Hi Basie did you come right with your Ranger?
Johansson from other a year ago
Did you found what was wrong?
Comment

Car cranking but won't start

Ford Ranger 2015 Pickup ute 220000 miles
Cranking but won't start... changed fuel filter,air filter and cleaned up the fuel thank but still won't start...power train light is on
Iamo from other 5 years ago  
IA
36 reports 
Fred from Australia 5 years ago
Gday ive got a 2008 ford ranger deisel its been serviced by ford it cranks ovder but wont start any ideas
Amrish from other 3 years ago
I have the same problem with my Ford ranger 2015 3.2 5cilinder
Ben kgaphola from South Africa 2 years ago
I have a verry same problem please help
Weeksy from Australia 2 years ago
Same issue. Been back to ford twice but problem still there. Only happened since they put new motor in it.
Andre from other a year ago
I have a 2016 ford ranger 3.2 auto with tik tak noise or tapping noise from top cylinder,have changed injectors,Hydraulic lifters but noise is still on and engine list performance as well. Any advice please
Ivan from Australia 10 months ago
Im just selling my 3.2 2014 model same issue. Mine has been told failed injector leaking fuel and not allowing correct pressure to build aswell as high pressure fuel pump shit itself. ( guessing due to working overtime to make up pressure loss from dying injector). The ticking noise ontop of motor without hearing yours andre may have been the sound of injectors firing i had taken mine to mechanics 12 months ago regurding ticks ( when injectors were good) and was told the noise is normal but due to location of injectors directly ontop of engine they are more audible than other motors where injectors are on the side. *** not a mechanic. Just what i was told by going on 10 mechanics trting to find issue with my ute***
Comment

Wont start SolvedSolved

Ford Ranger 1995 Ford ranger 150000 miles
I have no spark and no fule presher
Robert from United States 7 years ago  
RO
4 reports 
Solved
Best answer (according to Robert)
Robert from United States 7 years ago
We thought it was fixed but she drove tt to work and it died on the way back home and now we cant get it started we have no spark and no fule preaher
Mayhem motors from Australia 7 years ago
Could be a fuse or electrical short normal if it has been off road you could of knocked a censer wire loose
Comment

Injector Pump not Pumping diesel

Ford Ranger 2013 3.2L Xlt Double Cab 235000 miles
Hi aal,
I have encountered an issue with my Ranger about a week ago where i was driving on the Highway and all of a sudden the engine cut out. I did diagnostic test and glowplug 1&3 issues were detected. I removed the Feeding pipe of the Injector pump to the Pressure rail and when i turned the engine the Pump wasnt pumping any Diesel to the Pressure rail.
Is my Injector pump faulty ?
Piet from South Africa 5 years ago  
PI
59 reports 
Harry from Australia 2 years ago
What would you expect,its a European Ford peice of Crap
Macdonald from South Africa 2 years ago
What's injector pump fault
Macdonald from South Africa 2 years ago
Diseal is coming from the tank until diseal pump is not going to injectors
Watson from other 8 months ago
You ever got this problem fix I’m having the same issue
Martin from South Africa a year ago
Hi, I also have this problem. Any tips or suggestions please?
Watson from other 8 months ago
You ever got the issue fix
Comment

Car Wont Start SolvedSolved

Ford Ranger 2016 Pickup,SA2K,T6 168000 miles
My ford Ranger had damaged pistons, so i ordered a new engine to replace the oldone. Once the new engine was fitted, i drove i for 3 days before it shutdown and wont start. It cranks.
Yohane from South Africa 3 years ago  
YO
1 report 
Solved
Best answer (according to Yohane)
Yohane from South Africa 3 years ago
We replaced the old Fuel Injectors and the car worked fine. I was told that if new injectors are fitted, the on board computer needs to be reprogrammed
Comment

Transmission vibrations SolvedSolved

Ford Ranger 2012  50000 miles
My van started having huge vibration problems at speeds between 5-40 mph. All the car's crosspieces have been replaced and now the vibration is softer but still well noticeable at speeds between 25-40 mph. All the engine, box and exhaust holders have been checked, the tires have been serviced and the drive shaft has been turned to crankshaft in 180 degrees, but the vibration is still there. What can it be?
SUE from United States 9 years ago  
SU
7 reports 
Solved
Best answer (according to SUE)
Roland from United States 9 years ago
Lay yourself under the car and check that the drive shaft or Cardan shaft is properly installed.The differential is quite difficult, so you should check the cross-pieces
SUE from United States 9 years ago
Roland, thanks for your help. Effectively, the cross-piece that was installed linked together with the differential was presenting some vertical moves. It will be changed.
Comment

STNDRD on dash board.

Ford Ranger 2003 Double cab, xlt, pick up 80000 miles
When I start the ignition the engine doesn't start, but while it is cranking all the lighting system i. E. Headlamps, indicators, etc, are all blinking on & off and 'STNDRD' is shown on the information display in the instrument cluster. Pls help identify this problem. Thanks.
Tomo from other 2 years ago  
TO
23 reports 
Andryde from other 2 years ago
All the indicators are blinking on and off and STANDARD is shown, brake pedal is stiff, distance of remaining fuel in tank turns to 0 and it wont start
Dave from New Zealand 2 years ago
Same issue here, have you had any more information on a remedy? I might get an electrician to have a look, it's a bit beyond me
dudu from South Africa 2 years ago
Same problem here it's not sturting
Comment

Power loss and jerks

Ford Ranger 1993  120000 miles
When speeding up, it loses power and jerks every now and then. When reducing the speed, in 3rd or 2nd gears, explosions are heard. When starting the car, the engine is powerless and only after two minutes or so it stabilizes.
providence from United States 8 years ago  
PR
16 reports 
Issy from United States 8 years ago
Check: oxygen sensor, DIS module, spark plugs wiring and coils.
Ian21 from South Africa a year ago
Crank shaft sensor. Trust me
Comment

Engine light on will not start

Ford Ranger 2011  250000 miles
Engine light came on engine started then shut off and will not start a will not start again
Roger from Australia 3 years ago  
RO
7 reports 
Roger from Australia 3 years ago
All, the engine light came on and the car slowed down, stopped on the side of the road, turned it off. Then turned the car back on and had a noise coming from under the bonnet, shut it off and now will not start. Anyone know of the main reason? anyone in Perth australia with a diagnostics computer to plug it in and see what is the problem. I asked 1 Ford dealer and told me to bring the car in, just need to know if anyone has or knows of anyone who would ahve the computer to plug it in and find the fault.
Andrew from Canada 3 years ago
On my 2009, 2.3 litre Ranger, all gauges have switched off except for fuel and the engine locks down as soon as it is turned off. Two garages have tried to find the problem but failed. In the past, it has occasionally happened while being driven but the engine has kept on going until it righted itself in a few minutes. Now, it is parked and the engine is locked (with only the fuel gauge working). Any ideas?
Comment

Stalls when driving

Ford Ranger 1996  180000 miles
Hi everyone, please help me. Some weeks ago, the ABS light started turning on occasionally and it now remains this way. I don't know if it has something to do but I've noticed the air conditioning is not working any more. After driving for some minutes in the city, I noticed a power loss; the vehicle slowed down and suddenly felt a jerk as if the engine wanted to stall. This event repeated two to three times until it finally stalled. At that moment, the engine could only be started after the third attempt. The following day, after driving for three blocks, the car stalled. In this opportunity,… Read complete
submit from United States 9 years ago  
SU
12 reports 
bess80 from United States 9 years ago
Check the engine's ground wire, it might be that the heat or movements made the screw loosen or get damaged, as everything you are talking about is electric. It might be that with the jerks and movements, the computer has desprogrammed and that is why it is giving that failure. Check it as well.
Chippydips from Australia 6 years ago
Check the EGR valve, as these valves basically need replacing usually after 150000kms
Comment

Temperature raise SolvedSolved

Ford Ranger 2005  450000 miles
When the temperature is at its normal range, water starts to leave the deposit and, when there is a water deficit, the temperature raises. The odd thing is that the hose that carries water to the pump is always cold, even the hose that leaves the thermostat, and they are hoses that enter the superior part of the radiator and thus should be hotter. It seems as though water was not flowing. The thermostat is new, so it might be a housing failure, as the gasket was changed for a new and original one.
caleb from United States 9 years ago  
CA
9 reports 
Solved
Best answer (according to caleb)
mandy from United States 9 years ago
Buddy, your thermostat housing is damaged, so it is opening even with low pressures.
Comment

Not starting at all now

Ford Ranger 2012 2.2 diesel ford ranger  15000 miles
At first it had a hard starting for such a long time maybe for two weeks, but when you pull it or give at quick starting the engine run quick but when you try to run it using the key it won't start
Anaf from South Africa 3 years ago  
AN
3 reports 
chiripa from South Africa 3 years ago
Not starting it pushing smoke through inlet manifold, to the turbo pipe
Petrolhead from South Africa 7 months ago
I'm having the same issue,starts with quick start but doesn't without,I have changed injectors and coded them replaced the seal on the high pressure pump and still not starting just cranks and stops seems like a fuel or fuel pressure issue please assist
Comment

Check Engine Light

Ford Ranger 2008 3 Litre 5 Speed Diesel Turbo 270000 miles
Code Po500 Changed Speed Sensor Unit And Reset Light Comes Back On After I Travel 80 To 90 Kms Car Drives Fine Speedo Works Fine Can Any One Help,
Redman from Australia 7 years ago  
RE
18 reports 
Stuey from Australia 6 years ago
Our ranger was reversing our boat up on grass in 4 low and had a jerking type result and made it quite hard to put the boat away any answers cheers
Redman from Australia 6 years ago
What has That Got To do With My question
Comment

Truck runs rough and stall out of the blue

Ford Ranger 1993 4.0 26800 miles
The motor runs rough and stalls out of the blue we have changed the fuel pump and injectors, plugs plug wires throttle position sensor checked the mass air flow and it is reading fine fuel pressure is good the check engine light will come on but it will not show a code had it put on computer and it shows every thing is working fine also changed the fuel pressure unit
cstrief from United States 8 years ago  
CS
18 reports 
Cqmanager from Canada 7 years ago
Try cleaning your injectors...alot of times they get fouled up and why it stalls... seafoam or equivalent has always worked for me
Comment

Glow plugs light not working, diesel pump not distributing diesel to i

Ford Ranger 2006 Wlt  253000 miles
Trying to start engine , but no diesel into injectors
Tla1243 from South Africa a year ago  
TL
2 replies 
Bruce from United States a year ago
If the glow plugs light is not working and the diesel pump is not distributing diesel to the injectors, it could be a problem with the fuel system or a malfunctioning component.
Here are a few things you can try:

Check the fuel pump. The fuel pump is responsible for delivering diesel fuel from the tank to the injectors. If the fuel pump is not functioning properly, it could cause the engine to not start or run poorly. You can test the fuel pump by listening for a humming noise when the key is turned to the "on" position.
Check the fuel pump relay. The fuel pump relay is responsible for providing power to the fuel pump. If the fuel pump relay is not functioning properly, it could cause the fuel pump to not receive power and the engine to not start or run poorly. You can test the fuel pump relay by checking for voltage at the fuel pump connector.
Check the fuel filter. A clogged fuel filter can restrict the flow of diesel fuel and cause the engine to not start or run poorly.
Check the fuel lines. If the fuel lines are damaged or leaking, it could cause the engine to not start or run poorly.
If you are unable to identify the source of the problem or if the issue persists after checking these components, I recommend having a mechanic diagnose and repair the issue to ensure that the problem is properly addressed and the vehicle is safe to drive.
Nicoleen from South Africa 7 months ago
Why is there pressure on injector 4. The fuel line pipe keeps falling out at injector 4 causing the diesel to run out badly.
Comment

Ford ranger 3.2 6 Speed wont start

Ford Ranger 2010 Picknup 150000 miles
I was driving my vehicle and it started stalling and hesitating to pick up and when I parked it, it started jerking while idling. Then I drove a short and it the engine just stopped running. I started again and it completely refused To start and it just kept cranking. After checking the intake pipe from engine into the fuel filter chamber, fuel was not flowing when I cranked the engine
Real from other 2 years ago  
RE
1 report 
Bigboi from New Zealand 2 years ago
It could be your cranking sensor causing this
Jay jay from other a year ago
My 2004 ford ranger will not accelerate pass 2000 rpms
Comment


Problems with a Ranger? Share them
Submit commentCancel
Submit replyCancel


Did you find the website helpful?

Thank you!